Author Topic: [HELP]Deal with the cross of the wall!  (Read 4332 times)

0 Members and 1 Guest are viewing this topic.

cjw

  • Guest
[HELP]Deal with the cross of the wall!
« on: March 10, 2009, 01:20:37 AM »
May be post the picture could express clearly.

After think with my best,still have no idea.

Just guess.may be could solve it by "break",however No way out.

TheSwamp super man(may be woman?)...please help!

cjw

  • Guest
Re: [HELP]Deal with the cross of the wall!
« Reply #1 on: March 10, 2009, 01:26:43 AM »
The animation: (My stupid method)

CADaver

  • Guest
Re: [HELP]Deal with the cross of the wall!
« Reply #2 on: March 10, 2009, 01:44:45 AM »
even your way would be faster if you turned off the red layer.

FengK

  • Guest
Re: [HELP]Deal with the cross of the wall!
« Reply #3 on: March 10, 2009, 01:47:33 AM »
I think this should help, Thanks to CAB. Some tweaking might be needed.

TimSpangler

  • Water Moccasin
  • Posts: 2010
  • CAD Naked!!
Re: [HELP]Deal with the cross of the wall!
« Reply #4 on: March 10, 2009, 07:08:49 AM »
Here are 3 routine that I use

One for T intersections.
One for X intersections
One for L intersections

I have collected these from various places, put them together and tweaked them to work.  There is much room for improvement.  Enjoy
ACA 2015 - Windows 7 Pro
All Comments and Content by TimSpangler, Copyright © 2016

cjw

  • Guest
Re: [HELP]Deal with the cross of the wall!
« Reply #5 on: March 10, 2009, 10:55:49 AM »
Here are 3 routine that I use

One for T intersections.
One for X intersections
One for L intersections

I have collected these from various places, put them together and tweaked them to work.  There is much room for improvement.  Enjoy

Thanks very much,TimSpangler

and thank you CADaver , xycadd

Spike Wilbury

  • Guest
Re: [HELP]Deal with the cross of the wall!
« Reply #6 on: March 10, 2009, 10:58:53 AM »
Or... you can draw the center lines, and type the width and all of the cleaning can be done with:

AutoWalls.-

http://www.theswamp.org/index.php?topic=7180.msg88472#msg88472


Maybe...

uncoolperson

  • Guest
Re: [HELP]Deal with the cross of the wall!
« Reply #7 on: March 10, 2009, 11:10:21 AM »
mledit

wizman

  • Bull Frog
  • Posts: 290
Re: [HELP]Deal with the cross of the wall!
« Reply #8 on: March 10, 2009, 02:03:42 PM »
also you can,

draw centerline (use one polyline  leaving one point of the star open like in your figure), then offset  the centerline inside and offset outside then you can arrive at your figure.  It only works for open polylines with start and endpoints not coincident.

cjw

  • Guest
Re: [HELP]Deal with the cross of the wall!
« Reply #9 on: March 10, 2009, 11:58:03 PM »
Or... you can draw the center lines, and type the width and all of the cleaning can be done with:

AutoWalls.-

http://www.theswamp.org/index.php?topic=7180.msg88472#msg88472


Maybe...

Luis,
wawa,AutoWalls is amazing. Good work.
Thank you...

cjw

  • Guest
Re: [HELP]Deal with the cross of the wall!
« Reply #10 on: March 10, 2009, 11:59:09 PM »
mledit

The wall and center is "LINE" ,already.

cjw

  • Guest
Re: [HELP]Deal with the cross of the wall!
« Reply #11 on: March 11, 2009, 12:01:25 AM »
also you can,

draw centerline (use one polyline  leaving one point of the star open like in your figure), then offset  the centerline inside and offset outside then you can arrive at your figure.  It only works for open polylines with start and endpoints not coincident.


I don't quite understand. hehe :lol:

wizman

  • Bull Frog
  • Posts: 290
Re: [HELP]Deal with the cross of the wall!
« Reply #12 on: March 11, 2009, 12:27:54 AM »
also you can,

draw centerline (use one polyline  leaving one point of the star open like in your figure), then offset  the centerline inside and offset outside then you can arrive at your figure.  It only works for open polylines with start and endpoints not coincident.


I don't quite understand. hehe :lol:



sorry for confusing, here's a gif:




cjw

  • Guest
Re: [HELP]Deal with the cross of the wall!
« Reply #13 on: March 11, 2009, 03:03:48 AM »
After think long time...
I find a way to make it work...

with the method: region union

look this


Spike Wilbury

  • Guest
Re: [HELP]Deal with the cross of the wall!
« Reply #14 on: March 12, 2009, 10:06:54 AM »
That's looks good CJW,

And that's also the beauty of AutoLISP... :)